A vintage No.350 mushroom head metal forming stake or stake anvil.Marked '350' to one side.4 inch (100mm) diameter mushroom head or face, a few minor ...

A nice antique smiths' stake anvil or anvil stake.Typically fitted into a wooden bench block before use.57/16 inches (137mm) total length including th...

A nice vintage Archimedean drill.Hardwood head stock and handle with line detail.4 jaw brass chuck with steel collar and one bit.All parts move freely...

What we believe to be an assay sponsor's or maker's mark.For use in hallmarking jewellery or other precious metal ware.The mark made is an embossed 'D...

A vintage ball or mushroom head metal forming stake or stake anvil.17/8 inch (48mm) diameter round head or face.The shank tapers from 21/8" (54mm) squ...

An interesting vintage ball pein or peen hammer.Probably a conversion by the previous owner and ideal for tight spaces.13/16 inch (24mm) diameter dome...

A very good large ball pein or peen hammer by BEDFORD TOOLS of Sheffield.Marked 'BEDFORD ENGLAND 1 1/2 LB' to one cheek.11/4 inch (32mm) diameter face...

A probably unused vintage blacksmiths' 1/2 inch bottom swage.Believed to be by WHITEHOUSE of Atlas Forge.Marked '1/2' to one side.The head is approxim...

A probably unused vintage blacksmiths' 1/4 inch bottom swage.Marked '1/4' to two sides.The head is approximately 25/16 by 21/2 inches (59 x 65mm).The ...

A probably unused vintage blacksmiths' 3/8 inch bottom swage.Marked '3/8' to one side.The head is approximately 25/16 by 21/2 inches (59 x 65mm).The s...

A little used vintage blacksmiths' bottom fuller.29/16 inch or 65mm wide.The shank is 2" (51mm) long and 11/8" (30mm) square.Retains the majority of i...

A good vintage blacksmiths' creasing iron stake anvil or creasing stake.9 by 17/8 inch (227 x 48mm) working surface with 9 creasing grooves.The shank ...

A very little used vintage blacksmiths' hardy cropper or hot cut tool.13/4 inch or 45mm wide.The shank is 2" (51mm) long and 11/8" (30mm) square taper...

A good vintage blacksmiths' or tinmens' hatchet stake.10 inch (253mm) long by 11/16" (21mm) thick angled edge.The shank is 10" (253mm) long and 11/4" ...

A small vintage, or most likely antique, natural oil stone or razor hone in a bespoke hardwood box.This stone measures approximately 33/8 inches (86mm...

A good vintage planishing hammer from BUCK & HICKMAN.Marked '& HICKMAN' to one cheek with an 'S' within a diamond border to the opposite side,...

2 good pairs of vintage GILBOW 245 tin snips.1 each of 8 and 10 inch.Both are marked 'G245' near the joint with 'GILBOW SHEFFIELD ENGLAND' cast into t...

A good pair of vintage MONUMENT BRAND wing dividers or compasses.Marked 'MONUMENT BRAND' on one leg.Also stamped '43' with the military Broad Arrow ma...

An interesting piece of petrified or fossilised wood.At least a few hundred thousand years old and most likely much older.This piece is approximately ...

A good pair of vintage wing dividers with fine adjustment by PEXTO USA.Marked 'PEXTO MADE IN USA 7' to the top of one leg.Brass joint.All parts move f...

A scarce vintage PRIORY Tools wooden display stand.PRIORY brand tools have been produced by SMITH FRANCIS TOOLS of Birmingham since 1934.This wooden d...

A small vintage Archimedean drill.Complete with 5 bits, please see images.Beechwood head stock and handle with line detail.The cap of the head stock r...

Thirteen unused 1/2 inch square SPEEDWELL SUPER tool bits by George SOUTAR & CO of Sheffield.7 of the bits are 21/2 inches in length, the other 6 ...