A very tidy and scarce Shaw's patent SARGENT No.10 smoothing plane.These planes were only offered in the SARGENT range for a limited period between 19...

A scarce early American STANLEY No 72 chamfer plane, believed to be a type 2 circa 1886 - 1904.Marked 'STANLEY' on the left side of the main casting w...

A scarce early model of the PRESTON No.9 smoothing plane.This early example differs to the later No.9s in that it has none of the red paint of the lat...

A No.1464 RABONE boxwood hatters' rule.Marked 'J.RABONE & SONS MAKERS No1464' on one edge.Divided into eighths on the top and brass slide with 'si...

A good 14 inch (actual 141/16") infill panel plane.Brass lever cap with attractive knurled screw.Fitted with a good length 27/16 inch HEARNSHAW BROTHE...

A small 1/2 inch wide infill shoulder plane.Marked 'T' on the heel and believed to be by William THACKERAY of Leeds.Rosewood infill and wedge with muc...

An interesting smaller than usual dovetail smoothing plane by MATHIESON of Glasgow.Only 7 inches overall length and similar to the model No.842 improv...

A scarce smaller antique dovetailed mitre plane by Stewart SPIERS of Ayr.At only 8 inches overall length, this wedged plane is an unusual size as wedg...

A wonderful skew back SPEAR & JACKSON 88 A rip cut panel saw.The blade etching reads 'MADE EXPRESSLY FOR W.DOVE & SONS YORK'.  William Dove &a...

A very scarce antique dovetailed mitre plane by Stewart SPIERS of Ayr.This mitre plane has the rare inverted cupid's bow bridge marked with the upside...

A very good STANLEY 140 skewed block plane.Believed to be an early type 2 example.The removeable side plate is marked 'PAT NOV 6 94'.Knurled flat top ...

A scarce American STANLEY No.289 fillister and rebate or rabbet plane.Produced from 1911 to 1948 and rarely seen on this side of the Atlantic.Fitted w...

A scarce early STANLEY No 62 low angle jack plane.Produced between 1905 and 1942.This example has the 'B' casting mark on the inside of the depth adju...

A very good example of the rare STANLEY No.69 hand beader.Produced by STANLEY from 1898 to 1917 and far harder to find than the No.66 beader.'STANLEY ...

A wonderful TISSOT repousse hammer.Marked 'L.HUGONIOT TISSOT' with the Crown trade mark.Bulbous rosewood handle with boxwood wedge.11/8 inch convex fa...

A very tidy and unique NORRIS A5 smoothing plane.This post war example has been in the same collection since the 1950s and its previous owner replaced...

A scarce and little used registered design wooden auger handle with three patent GILPIN bits.This beechwood auger handle is possibly by GILPIN but is ...

An interesting early 20th century adjustable smoothing plane by NORRIS of London.This parallel sided cast steel plane is not listed in any of the NORR...

An interesting and unusual double tongue plane by ROBERT BEWLEY of Leeds, circa early to mid1800s.To cut two parallel tongues, each approximately 1/4 ...

An unusual brass and rosewood marking gauge.This craftsman made gauge has two brass slides.With a 51/2 inch long 13/16 inch rosewood square stem and 2...

A very attractive craftsman made side rabbet or rebate plane.Gunmetal casting with shapely central moulding.Fitted with matching MARPLES blade irons, ...

An unusual wooden compass plough plane by C JACOB of Strassburg (Strasbourg).Marked 'C JACOB STRASSBURG' on the toe, although Strasbourg is part of Fr...

A very unusual small grooving plane by VARVILL of York.Marked 'VARVILL & SONS LTD EBOR WORKS YORK' on the toe.Also marked 'GARANTEED BY GP PRESTON...